우수한 성능 그대로. 채널 수는 두 배로.

새로운 모드의 펌웨어 업데이트 3.0으로 개선된 스펙트럼 효율성

Digital 6000에 채널의 수를 두 배로 늘려 사용할 수 있는 링크 덴시티 (Link Density) 모드가 추가되었습니다.
이제 매우 혼잡한 주파수 스펙트럼에서도 다양한 규모의 사용 환경에서 맞게 추가 주파수 옵션을 사용할 수 있습니다. 이 새로운 모드는 시리즈의 모든 구성 요소와 작동하며, 펌웨어 업데이트를 통해 사용이 가능합니다.

간단하고, 쉽고, 효율적인

스튜디오나 무대 그 어떠한 환경에서도 탁월한 성능을 발휘하도록 LD 모드를 설계했습니다. 이동량이 많거나 무대 의상 속에서 땀이 나도 그 어떠한 문제 없이 작동합니다. 실험실 조건뿐만 아니라 세계적인 무대에서도 젠하이저의 우수한 기술은 인정 받았습니다.

간단하고, 쉽고, 효율적인

우수한 성능

링크 덴시티 모드에 새로 개발된 젠하이저 퍼포먼스 오디오 코텍 (SePAC)을 사용해서 데이터 속도를 최적화했습니다. 채널 간격은 등거리로 200 kHz로 감소해서 이제 1 MHz 대역폭에서 5개의 채널이 사용 가능합니다. 보다 다양한 상황에서 새로운 가능성으로 우수한 성능을 경험해 보세요.

우수한 성능

효율성과 폭넓은 가능성

새로운 D6000 링크 덴시티 모드로 선택의 폭이 넓어졌습니다. 사용 환경에 맞는 대역, 채널 수 및 데이터 속도를 완벽하게 제어할 수 있을 뿐만 아니라, 가장 까다로운 환경에서도 원하는 대로 폭넓게 활용할 수 있습니다.

효율성과 폭넓은 가능성

FAQ

  • Which devices can use Link Density (LD) mode?

    • Link Density (LD) mode can be used on EM 6000, EM 6000 Dante, SK 6000, SKM 6000 and SK 6212.
      Digital 9000 receivers and transmitters and the EK 6042 receiver are not supported.

  • What are the system requirements to activate Link Density (LD) mode?

    • Both receiver and transmitter must have at least the following firmware versions:
      • EM 6000: 3.0.4
      • SK 6000 / SKM 6000: 1.1.51
      • SK 6212: 1.3.23
      The latest firmware can be found at www.sennheiser.com/download with the keyword “Digital 6000”. Wireless System Manager (WSM) software is required for the update and can be downloaded free of charge at www.sennheiser.com/wsm.
      The new firmware versions are supported by all systems on the market.

  • Is the firmware update for Link Density (LD) mode subject to charge?

    • No, this update is available to all users free of charge.

  • How to change the transmission mode in the EM 6000?

    • Activate the system menu and scroll to "Transmission Mode”. The “Transmission Mode” menu item enables the receiver to switch between LD (Link Density) and LR (Long Range) mode.
      As both channels of a unit always operate in the same mode, both channels are switched simultaneously.
      The selection of LD or LR mode can also be made via WSM in the EM 6000's instrument settings. The RF Mode property selects between LR or LD mode.
      After switching modes, the receiver will restart.

  • How to change the transmission mode in the Digital 6000 transmitters (SK 6000, SK 6212, SKM 6000)?

    • Once the desired mode (LD or LR) has been activated in the EM 6000, the receiver will prompt to perform an infrared synchronization of transmitters. The LD / LR mode cannot be updated directly via the transmitter menus, a synchronization must be performed.
      All SK 6212 as well as SK 6000 and SKM 6000 from serial number 1469xxxxxx can be switched over via Sync. SK 6000 / SKM 6000 with serial numbers below 1469xxxxxx require a firmware update for each transmission mode change, which is automatically started during Sync.

  • Why are different audio codecs used?

    • To operate twice as many channels in the same spectrum, the audio transmission data rate must be reduced. Link Density (LD) mode uses the Sennheiser Audio Performance Codec (SePAC), which limits the upper frequency range at 14 kHz.
      LR mode uses the Sennheiser Digital Audio Codec (SeDAC) for the highest audio demands and requirements.

  • Why do the two modes have different RF power?

    • To operate twice as many channels in the same spectrum, RF power must be adjusted. Link Density (LD) mode has been optimized to deliver excellent results on typical stage sizes, where maximum RF performance is not required. For maximum RF performance, LR mode is the ideal choice.

  • Can I use LR mode in one channel of an EM 6000 dual receiver and the LD mode in the other channel?

    • No, both channels of a device always work in the same mode. Both channels are switched simultaneously.

  • Can the two transmission modes be used in parallel in the same production?

    • Yes, this is possible on different receivers.

  • Does WSM software support LD mode?

    • Yes, as of version 4.4.6.

  • Do I have to use special antennas and antenna splitters for LD mode?

    • No, all antennas and antenna splitters for Digital 6000 can also be used with both LR and LD modes.

  • Does the Auto Setup of the EM 6000 support LD mode?

    • Not completely. Auto Setup will run in LD mode, but it utilizes the standard LR mode frequency banks, with 400 kHz equidistant spacing.
      Auto Setup is intended for smaller and simpler applications where the LD mode is not required. For large and complex configurations, we recommend our WSM software.

  • Does the battery life of the transmitter change in LD mode?

    • No, the selected transmission mode has no significant influence on battery life.

  • Can the EM 9046 or EK 6042 be retrofitted with LD mode?

    • No, retrofitting is not possible.