HMD 46
제품 선택하기
ATC 헤드셋, 개방형

HMD 46-3-6는 관제사용 초경량의 편안한 개방형 붐세트로 항공 교통 컨트롤에 이상적인 모델입니다. 이 헤드셋에는 ActiveGard™ 기술이 적용되어 음향 버스트로부터 관제사의 청각을 보호해 줍니다.

  • 초경량

  • 특허 취득한 2-조각 자동 헤드밴드와 부드러운 이어패드로 우수한 착용감 보장

  • 확 젖혀지는 헤드폰 디자인

  • 유연한 마이크로폰 붐으로 왼쪽 또는 오른쪽으로 착용 가능

  • 선명한 음성 전달하는 노이즈 캔슬링 콘덴서 마이크로폰

  • 손쉬운 교체가 가능한 헤드셋 한쪽에만 있는 케이블 (길이 1.85 m)

  • PTT와 함께 이용 가능

  • ActiveGard는 음향 버스트로부터 사용자의 청각을 보호해줌

상품평
Be the first to write a review.

Specifications
구성품
  • HMD 46 헤드셋
  • 케이블 집게
  • 팝필터
  • 사용설명서

Support
연락처
Product Support Phone

Product Phone


FAQ
  • What are NRR (Noise Reduction Ratings) for a headset?

    NRR (Noise Reduction Ratings) is a rating of the passive reduction of a headset and this is by a set standard (ANSI).

    However there are no present standards for measuring ANR (Active Noise Reduction). Each Manufacturer uses their own standards. Sennheiser uses the standards and results of an independent laboratory that is accredited by the National Institute of Standards and Technology. One should be very careful in assuming that all manufacturers use these results in a fair and unbiased way.



  • Which accessories come with my ATC/C3 headset purchase?

    Your purchase of a Sennheiser ATC/C3 headset will include a windscreen, clip, bag, and manufacturer certificates.



  • Active Noise Cancellation

    Active noise cancellation is the reduction of noise, particular in the low frequency range, by using active noise compensation electronic circuitry. Active noise cancellation is measured in decibels (dB).



  • Caliper Pressure (Contact Pressure)

    Caliper Pressure (sometimes referred to as Contact Pressure) is the amount of force applied to the sides of the head while wearing headphones. Caliper pressure is measured in Newton’s (N) and could range from 1.6 N (loose fit) to 10 N (snug fit).

    A tight coupling between the headphone and the ear is necessary in order to maximize passive attenuation however too much pressure can make the headphone uncomfortable to wear for long periods of time. 



  • Condenser Microphone (Electret Microphone)

    A CONDENSER or ELECTRET microphone is one that is based on an electrically charged diaphragm (or back plate) assembly which forms a sound-sensitive capacitor.

    On a condenser or electret microphone a very thin metal or metal coated-plastic diaphragm is mounted just in front of a ridged metal or metal-coated-ceramic back plate. This assembly is known as a capacitor (condenser) which has the ability to store a charge or voltage. When the element is charged an electrical field is created between the diaphragm and the back plate proportional to the spacing between them. Sound waves vibrate the diaphragm and it is the vibration of this spacing due to the motion of the diaphragm relative to the back plate that produces the electrical signal corresponding to the sound picked up by a condenser microphone. 

    The construction of a condenser microphone must include some provision for maintaining the electrical charge or polarizing voltage.

    NOTE: An Electret condenser microphone has a permanent charge maintained by a special material (Electret) deposited on the back plate or on the diaphragm.



  • Diaphragm

    The diaphragm is a  thin membrane in a microphone which moves in response to sound waves.



  • Dynamic Microphone

    A DYNAMIC microphone employs a diaphragm/voice coil/magnet assembly which forms a miniature sound-driven electrical generator.

    Sound waves strike a thin plastic membrane (diaphragm) which vibrates in response. A small coil of wire (voice coil) is attached to the rear of the diaphragm and vibrates with it. The voice coil itself is surrounded by a magnetic field created by a small permanent magnet. It is the motion of the voice coil in this magnetic field that generates the electrical signal corresponding to the sound picked up by a dynamic microphone.

    Dynamic microphones have a simple construction and are economical and rugged. They can provide excellent sound quality and good specifications in all areas of microphone performance. They handle extremely high sound levels and it is almost impossible to overload a dynamic microphone.

    Dynamic microphone are relatively unaffected by extremes of temperature humidity.



  • Gain

    Gain is the amount of increase in audio signal strength. Gain is often expressed in decibels (dB).



  • Microphone Gain Control

    Microphone Gain Control is a  level control on a microphone preamplifier that sets gain and is used to prevent overload of a preamplifier.



  • Output Voltage

    Output Voltage is similar to sensitivity except it takes into account additional electronics used to amplify the signal. This is typically measured over a range of frequencies and will include the term + or - 3 dB. Rather than using 1 Pascal this specification may also include the input level used such as 114 dB at a distance of 6 mm.



  • Passive Attenuation

    Passive attenuation is the ability of the headset to reduce the ambient noise level by merely wearing the headset without the aid of any electronic assistance (ie: active noise compensation circuitry). Passive attenuation is measured in decibels (dB).



  • Pre-Amp

    A Pre-Amp is a low-noise amplifier designed to take a low-level signal (such as that from a microphone) and bring it up to normal line level.



  • Sensitivity

    Sensitivity  is a measurement of how much voltage is produced by a microphone for a specific measured input (1 Pascal). Sensitivity is measured in micro volts (uV) or millivolts (mV).

    A typical rating for a dynamic microphone would be 1 mV. A typical rating for an Electret microphone would be 3.5 to 10 mV A typical rating for an Electret with amplifier would be 170 mV. 

    The higher the number the stronger the signal produced by the microphone.



  • XLR-3 Connector

    The XLR-3 Connector is a single connector that can be used in place of the PJ055 headphone and the PJ068 microphone plugs on some Sennheiser headsets.

    Pin 5 of this plug can also be used to provide aircraft power for the NoiseGard power supply on some Sennheiser headsets.



  • XLR-5 Connector

    The XLR-5 connector is a single connector that can be used in place of the PJ055 headphone and the PJ068 microphone plugs on some Sennheiser headsets.

    Pin 5 of this plug can also be used to provide aircraft power for the NoiseGard power supply on some Sennheiser headsets.



다운로드

  • 사용 설명서
    • Instruction manual - HMD 46 / HME 46 (1.5 MB) Download

  • EU Declaration of Conformity
    • EU Declaration of Conformity HD46_HMD46_45 (400 KB) Download

  • 고해상도 이미지